Jump to content

Texas deep freeze carnage thread


immamac

Recommended Posts

9 minutes ago, Shoxthemonkey said:

@ROFL BOX should chime in. Up here the damage comes from freeze and thaw cycles at the actual dam, that lift and separate the shingles allowing water to capillary in between them and damage the substrate. It takes several cycles to do this. I'm guessing that once your temps get back above freezing the ice will disappear in a single episode and with it the worry of water damage.  They manufacture sno-blocks that keep ice dams from forming  and also retard avalanche situations from  roofs but I doubt that you get enough snow and ice to warrant them. I'm far from expert but I doubt that you have a lot to worry about. If you can reach them, knock them out. If you can't, oh well. Don't try to get up on your roof. Good luck.

Literally just learning about ice dams. Walked outside to see ice forming down one of the cedar columns on our front porch and icicles forming on one of the porch overhang vents. Knew it wasn’t a bad roof as it’s relatively new and had been recently inspected. Glad I read about this and hopefully it’s just this spot. Will try and knock as much of it off as possible when I get home. 

Link to comment
Share on other sites

21 minutes ago, TexasEd said:

Cost vs return.

The reason you can do that with electrical is every circuit has a run all the way back to the switch panel.  For safety in adding ceiling fans or preventing fires with a short circuit each one can be tripped or shut off independently like if you drop the hair dryer in the tub. (Of course that is on a GFCI for added protection)

To have the equivalent in a home you would have to do that twice for every faucet (hot and cold) water.  When we had copper pipes the expense was high and there was little benefit, no-one would die if you had to shut down the whole house.  It might make sense using Pex cost wise, I don't know but you could probably throw that cost into additional insulation and freeze proof outdoor bibs and get a better return.

that manifold system is only a few hundred bucks on supply house.  I know everyone is price sensitive, but I think production builders just don't want to do it and homeowners don't know it's out there.  it actually looks like less than $500 in additional material and labor to hook it up.

 

edit - you're right, she just said what you said.  you have to run every single line as a separate line instead of daisy-chains or loops.  she said though it's still a good thing to have.

Edited by troph
  • Hook 'Em 1
Link to comment
Share on other sites

4 minutes ago, troph said:

that manifold system is only a few hundred bucks on supply house.  I know everyone is price sensitive, but I think production builders just don't want to do it and homeowners don't know it's out there.  it actually looks like less than $500 in additional material and labor to hook it up.

 

edit - you're right, she just said what you said.  you have to run every single line as a separate line instead of daisy-chains or loops.  she said though it's still a good thing to have.

PEX is not approved in quite a few older, fancier building code jurisdictions.  Or just recently if at all.

Link to comment
Share on other sites

@Biff Tannen

Where do you live?

If you or anyone needs help & are close to Oak Hill / Dripping Springs / Wimberley / Spicewood / Bee Cave & need roofing or plumbing [limited, non licensed] assistance, please call or text me @ 512.656.6635.

Pics are helpful but not required.

Sent from my SM-G950U1 using Tapatalk

  • Hook 'Em 3
  • Like 1
Link to comment
Share on other sites

5 minutes ago, ROFL BOX said:

@Biff Tannen

Where do you live?

If you or anyone needs help & are close to Oak Hill / Dripping Springs / Wimberley / Spicewood / Bee Cave & need roofing or plumbing [limited, non licensed] assistance, please call or text me @ 512.656.6635.

Pics are helpful but not required.

Sent from my SM-G950U1 using Tapatalk
 

Just screenshotted this for future reference. 

  • Like 1
Link to comment
Share on other sites

32 minutes ago, ZB'Tejas said:


Welp. Hair dryer got the pipes into the Rinnai unit unfroze and once did the it tried to start up but then starting pouring water from the back of the unit.

Cut off the pipes for now as I guess I’m going to need a new unit. Dammit. And now I guess I need to worry about those pipes refreezing now that they have water and it’s shut off. Ugh


Sent from my iPhone using Tapatalk

That sucks. Sorry to hear 

Link to comment
Share on other sites

26 minutes ago, troph said:

love my builder girlfriend... hey baby come look at this, I think we might want one.... "oh yeah, I already have that in the plans."

That is exactly the system that I have. My house is smallish, 2300 sq ft in 2 levels, so all of my runs are short. I have never taken the time to trim and organize my installation. That looks pretty cool. Viega is just down the road from me and a couple of my golf buddies are engineers there. I got my unit at their cost 20 years ago and I was in for very little expense. I'm well insulated so I have never had to drain a line for freeze prevention. It makes it a snap to replace water heaters or faucets.

You need to be very careful when attaching lines to the manifold. It's all plastic and it is possible to crack the unit if you put too much torque to a fitting. Don't ask me how I know.

Edited by Shoxthemonkey
  • Hook 'Em 1
Link to comment
Share on other sites

17 minutes ago, troph said:

love my builder girlfriend... hey baby come look at this, I think we might want one.... "oh yeah, I already have that in the plans."

Pex is vulnerable to rodents chewing through the lines.  I love the idea of a pex manifold, but something to consider based on site.  

Link to comment
Share on other sites

16 minutes ago, TwiceHorn said:

PEX is not approved in quite a few older, fancier building code jurisdictions.  Or just recently if at all.

she uses it in Austin all the time.  It's now part of the international plumbing code she says. we are in the lakeway ETJ.

Link to comment
Share on other sites

10 minutes ago, ROFL BOX said:

@Biff Tannen

Where do you live?

If you or anyone needs help & are close to Oak Hill / Dripping Springs / Wimberley / Spicewood / Bee Cave & need roofing or plumbing [limited, non licensed] assistance, please call or text me @ 512.656.6635.

Pics are helpful but not required.

Sent from my SM-G950U1 using Tapatalk
 

Hyde Park.  Sun is out and stuff it starting to melt.  If this giant block of ice lets loose, it's going to land directly above my head and I'm going to freak out.  Luckily it will hit metal roof, so I'm hoping there won't be any damage.

Link to comment
Share on other sites

2 minutes ago, troph said:

she uses it in Austin all the time.  It's now part of the international plumbing code she says. we are in the lakeway ETJ.

Yeah, some cities have amended themselves out of that, at least until recently.  It had a checkered intro to the US, where our treated water deteriorated it real fast.

There are a few drawbacks, like the rodent thing Ana mentioned.  Copper has problems too. Mostly being a semi-precious metal.

Edited by TwiceHorn
Link to comment
Share on other sites

2 minutes ago, Anastasis said:

Pex is vulnerable to rodents chewing through the lines.  I love the idea of a pex manifold, but something to consider based on site.  

we are building with ICF (concrete blocks basically) and water lines will be on the inside of the concrete buried in the styrofoam.

  • Hook 'Em 2
Link to comment
Share on other sites

Just now, TwiceHorn said:

Yeah, some cities have amended themselves out of that, at least until recently.

There are a few drawbacks, like the rodent thing Ana mentioned.  Copper has problems too. Mostly being a semi-precious metal.

with what Austin requires these days, I think rodents are less of an issue.  her problem is the house is too tight.  but she also uses foam insulation and so the pex is hard for a rodent to get to I'm guessing.  I don't know about fancy jurisdictions, I think it's common to have clauses in county/rural building codes that say something like "and if nothing is specified, per international building/plumbing/fire code whatever whatever)

but point taken.

and even with rats, the manifold would be super handy.

Link to comment
Share on other sites

1 minute ago, Anastasis said:

Pex is vulnerable to rodents chewing through the lines.  I love the idea of a pex manifold, but something to consider based on site.  

I once had an estate case involving a shitty house in S. Austin.  Worth about $100k max.  Executor couldn't sell it due to deferred maintenance and neighborhood.  It had a few rat droppings, so one of the well-meaning relatives went over on his own and filled the house with rat poison, which, among other things, makes rats extremely thirsty.  Rats gnawed through the PVC lines under the kitchen and bathroom sinks looking for water and they burst opened and the rats drowned.  House was full of 6" water and floating rat carcasses.  Additional damage to house was so extensive that the executor ended up selling it for $60k.  

Lord I hope that place got torn down.

  • Hook 'Em 1
  • Haha 2
  • Fuck Around and Find Out 1
Link to comment
Share on other sites

3 minutes ago, troph said:

with what Austin requires these days, I think rodents are less of an issue.  her problem is the house is too tight.  but she also uses foam insulation and so the pex is hard for a rodent to get to I'm guessing.  I don't know about fancy jurisdictions, I think it's common to have clauses in county/rural building codes that say something like "and if nothing is specified, per international building/plumbing/fire code whatever whatever)

but point taken.

and even with rats, the manifold would be super handy.

No real point.  I'm sure yall know what you're doing.  People were asking about PEX and copper so I was kind of relating the pros and cons.

Link to comment
Share on other sites

Well I found the main cutoff valve down at the street. Tried turning it clockwise but it wouldn't budge. I'm afraid to fuck with it anymore than that since I don't know what I'm doing. Unable to locate the cutoff valve inside the house but I've narrowed it down and I think it's inside the wall.

Link to comment
Share on other sites

3 minutes ago, lockport said:

Well I found the main cutoff valve down at the street. Tried turning it clockwise but it wouldn't budge. I'm afraid to fuck with it anymore than that since I don't know what I'm doing. Unable to locate the cutoff valve inside the house but I've narrowed it down and I think it's inside the wall.

Just wack it with a hammer.

Link to comment
Share on other sites

1 hour ago, BrazilHorn said:

I will put a plug in for Counter Cafe off of 29th Street. They've been open.

Texas French Bread opened today for coffee and limited baked goods

Looked like Roppolos on the drag was open as well

I didn't go by but Lucky Lab off the drag/26th is supposed to be open as well for coffee/pastries

KoBoda Korean wing place open on drag as well. Dominos on 19th too

Link to comment
Share on other sites

8 minutes ago, dcar00 said:

heading for a new consecutive hours record.  32 hours now.   need 34 to set it.  will be 92 hours total from Thurs to Thurs.

AE says they have 90% up.  my guess is there will be a tweet from them saying 100% up and I will still be out. fuck these people.

Yeah this hasn’t been fair. Same thing is happening with my son down at San Marcos. 48 hours without and about 8 with and down again for 12+ hours.  Was frustrated with neighbors around us. They not once lost power that I know of. I know because they all had their porch lights on all day and night. They probably didn’t even realize it so I forgave them😁

Link to comment
Share on other sites

Just now, Spaulding Smails said:

75% of the calls we're getting are related to either exterior tankless water heaters or uninsulated copper pipes in attics, specifically those that have blown-in insulation.  Spray foam houses fared well and kept attic pipes above freezing temps. 

In Austin, right?  Didn't think it was warm enough for shit to start busting, but I guess it is.

It's ~30 in Dallas and my roof isn't dripping yet, but it's kind of sunny, so I guess any shit is going to reveal itself soon.

Link to comment
Share on other sites

Just now, TwiceHorn said:

In Austin, right?  Didn't think it was warm enough for shit to start busting, but I guess it is.

It's ~30 in Dallas and my roof isn't dripping yet, but it's kind of sunny, so I guess any shit is going to reveal itself soon.

Yes.  Austin.  We received 19 incoming leads yesterday for plumbing issues.  And, we're not even a plumbing company.  We JUST got our plumbing license last week, and I have ONE plumber on staff, so we're prioritizing existing customers.  Temps got above freezing yesterday for a bit, and issues started arising.

I'm hearing the big plumbing companies are telling folks mid to late March before they can even come out to look at a leak.  This is going to dwarf Hurricane Harvey from an insurance claim standpoint.  Lots of these issues are NOT minor.  We have five in queue that will potentially be $100K+ due to the damages sustained.

  • Hook 'Em 3
Link to comment
Share on other sites

3 hours ago, gmr548 said:

 


What you people have to understand is that this senior citizen and this dog were honored to sacrifice themselves to ensure Texas could avoid federal oversight of its power grid, and to make sure energy companies generate maximum profits.

Condolences to your friends, troph. Infuriating.

 

Federal oversight really helped California's power grid

  • Hook 'Em 1
  • Like 1
Link to comment
Share on other sites

Live in Houston where half block are new homes and half 1950s originals.  We all lost power for 36 hours. 

At 37th hour, almost simultaneously, my two neighbors in older homes had attic pipes burst.  A slew of us lucky ones spent a couple hours helping them clean up the mess.  Luckily, it was not whole house but they each lost a large rectangular portion of their ceiling and items under said ceiling.   Now, they are looking for places to live for a few weeks.

  • Hook 'Em 1
Link to comment
Share on other sites

3 hours ago, gmr548 said:

 


What you people have to understand is that this senior citizen and this dog were honored to sacrifice themselves to ensure Texas could avoid federal oversight of its power grid, and to make sure energy companies generate maximum profits.

Condolences to your friends, troph. Infuriating.

 

giphy-downsized-large.gif

  • Hook 'Em 2
  • Like 2
Link to comment
Share on other sites

power was out for about 50 hours but been on but for a few short outages since early yesterday morning.  having pressure issues with water now but other than that water has been good the whole time (pressure and hot/cold functioning).  dripping inside and wrapped outside.  if i continue to drip and no other obvious issues bw now and going above freezing for good tomorrow will i make it through unscathed?  

 

tldr if water continues to function are you out of the woods once it gets above freezing (meaning not vulnerable to busting when warming up since you've maintained flow the whole time?)

Link to comment
Share on other sites

2 minutes ago, Gale Snoats said:

power was out for about 50 hours but been on but for a few short outages since early yesterday morning.  having pressure issues with water now but other than that water has been good the whole time (pressure and hot/cold functioning).  dripping inside and wrapped outside.  if i continue to drip and no other obvious issues bw now and going above freezing for good tomorrow will i make it through unscathed?  

 

tldr if water continues to function are you out of the woods once it gets above freezing (meaning not vulnerable to busting when warming up since you've maintained flow the whole time?)

I have this same question

Link to comment
Share on other sites

1 hour ago, ROFL BOX said:

Re: PEX & deteriorating plastics / water, dont get that product mistaken with "KiTec".

http://www.kitecsettlement.com/faq.cfm

Sent from my SM-G950U1 using Tapatalk
 

Well, Kitec is a PEX product, although it is different from what is sold today.  One of its problems was that some of it was PEX-Aluminum-PEX and used brass/bronze connectors.  And that's worse than cats and dogs.

 

There was a more general problem with early PEX formulations used in the US.  Chlorine and fluoride deteritorated it.

Edited by TwiceHorn
  • Like 2
Link to comment
Share on other sites

2 hours ago, Anastasis said:

Pex is vulnerable to rodents chewing through the lines.  I love the idea of a pex manifold, but something to consider based on site.  

There are manifolds for copper as well. My house in Denver had it in the basement. It had steampunk (similar to below). It was built at the time of construction - and must have cost a pretty copper penny for all that copper. 

Pex appears the way to go to make this work. 

Quote

 

Copper:

65161d1355865124-copper-manifold-mfg-imag0185.jpg

(not my photo)

v.

Pex:

Are There Hidden Dangers with PEX Plumbing? - Fine Homebuilding


 

 

  • Drool 1
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



×
×
  • Create New...